Jump to content

[1.9.x] SXT Continued


Recommended Posts

5 minutes ago, voicey99 said:

Yes, unless there's some more modifications you'd like me to make to the changes (please do say if there's something you're not happy with)?

I haven't had time to look at it, I'm relying on you and @swjr-swis's review.

Ok, I'll see if I can get it out this evening

Thanks

Link to post
Share on other sites
On 11/9/2017 at 11:34 AM, voicey99 said:

In the raw download I used to modify it, they were written CR-NL but in the release they are CR. I guess you using Unix-like Linux (if your name is anything to go by) converts them.

"git clone" (assuming you have setup git correctly) should make that a non-issue, however there are also things the git repo owner can do to adjust things.

https://stackoverflow.com/questions/170961/whats-the-best-crlf-carriage-return-line-feed-handling-strategy-with-git

https://help.github.com/articles/dealing-with-line-endings/

 

Link to post
Share on other sites

New release, 0.3.18:

  • Thanks to @voicey99 for these:
    • Cut whitespace slightly
    • replaced spaces with proper tab spacing 
    • removed superfluous lines across all parts making the configs slightly smaller and easier to follow 
    • extended float curves for all engines that didn't have them already to beyond 1atm  (sorry, Eve landers, as per #35 )
    • correcting a few descriptions (grammar, spelling, old references etc.) 
    • increasing the fuel capacity (and dry cost/mass to match) of the Oscar-C, since its fuel capacity was terrible for its size.
  • Thanks to @Kerbas-ad-astra for these:
    •  Adding some tags to parts (so they can be found by their nicknames)
    • fix a couple of typos
    • adding CLS patches for parts yet unpatched.
       
Link to post
Share on other sites
  • 2 weeks later...
On 19/11/2017 at 3:04 AM, linuxgurugamer said:

If you make it, I will add it.

I am only maintaining this, not enhancing

Since you mentioned it...

I saw many tutorials on how to start fiddling with part creation,  but I am not sure which 3d modelling softwares are most indicated.... which one do you use? Can you suggest one that is good to start messing around a bit?

Link to post
Share on other sites
22 minutes ago, Daniel Prates said:

Since you mentioned it...

I saw many tutorials on how to start fiddling with part creation,  but I am not sure which 3d modelling softwares are most indicated.... which one do you use? Can you suggest one that is good to start messing around a bit?

I'm not the right one to ask, I don't do 3d modeling.

Better to ask someone like @RoverDude or @Angel-125

Link to post
Share on other sites
6 hours ago, Daniel Prates said:

Since you mentioned it...

I saw many tutorials on how to start fiddling with part creation,  but I am not sure which 3d modelling softwares are most indicated.... which one do you use? Can you suggest one that is good to start messing around a bit?

Blender.  It's free, and there are numerous tutorials widely available.

Link to post
Share on other sites

@Wolfair corp.

@linuxgurugamer

Hi, I am having an issue or a conflict between AoA and SXT. With AoA installed, the Elevons in SXT do not work.

The pics below are done with a clean install, a very new sandbox save, with the modulemanager files and the part database deleted each time before the game was ran. The one and ONLY difference between them is one was ran with AoA and the other was without.

Logs Without AoA

Logs With AoA

 

ULa0ieB.jpgJn7u4rX.jpg

Edited by TheKurgan
Link to post
Share on other sites

@linuxgurugamer

@Wolfair corp.

After more trial and error testing, I found if i remove the TestFin from AoA, then the SXT elevons work again... I can't figure out why, or where the conflict is, but that's as far as I can narrow it down.

Hopefully you intelligent guys can figure it out... I really enjoy both mods.... but I'm ok with that TestFin removed.

Link to post
Share on other sites
15 minutes ago, linuxgurugamer said:

Very strange.

Is ASET needed?

it isn't NEEDED, but it is required for the IVA's for AoA.

I can test or get fresh logs without it.

After Work.

I could remove EVERYTHING except SXT, Squad and AoA and test more if you like?

 

Link to post
Share on other sites
13 minutes ago, TheKurgan said:

it isn't NEEDED, but it is required for the IVA's for AoA.

I can test or get fresh logs without it.

After Work.

I could remove EVERYTHING except SXT, Squad and AoA and test more if you like?

 

If you could, it would certainly help.

I am hoping to get some time this evening to look at this.  Were they a CKAN install or manual?

Link to post
Share on other sites
  • Geonovast changed the title to [1.9.x] SXT Continued

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...