Jump to content

TOOB Parts: Attached Parts Location Change Far Out of Alignment With TOOB Fairing End When TOOB Is Not Vertically Aligned


Recommended Posts

Reported Version: v0.1.3 (latest) | Mods: none | Can replicate without mods? Yes 
OS: Linux Ubuntu 20.04.6 | CPU: AMD Ryzen 5 3400G | GPU: NVIDIA GeForce GTX 1080 Ti | RAM16GB


Specs: (Obtained from Steam via Help > System Information)


Computer Information:
Model: PRIME B450M-A
Form Factor: Desktop
No Touch Input Detected
Processor Information:
CPU Vendor: AuthenticAMD
CPU Brand: AMD Ryzen 5 3400G with Radeon Vega Graphics
CPU Family: 0x17
CPU Model: 0x18
CPU Stepping: 0x1
CPU Type: 0x0
Speed: 3700 MHz
8 logical processors
4 physical processors
Hyper-threading: Supported
FCMOV: Supported
SSE2: Supported
SSE3: Supported
SSSE3: Supported
SSE4a: Supported
SSE41: Supported
SSE42: Supported
AES: Supported
AVX: Supported
AVX2: Supported
AVX512F: Unsupported
AVX512PF: Unsupported
AVX512ER: Unsupported
AVX512CD: Unsupported
AVX512VNNI: Unsupported
SHA: Supported
CMPXCHG16B: Supported
LAHF/SAHF: Supported
PrefetchW: Unsupported
Operating System Version:
Ubuntu 20.04.6 LTS (64 bit)
Kernel Name: Linux
Kernel Version: 5.15.0-75-generic
X Server Vendor: The X.Org Foundation
X Server Release: 12013000
X Window Manager: GNOME Shell
Steam Runtime Version: steam-runtime_0.20230509.49499
Video Card:
Driver: NVIDIA Corporation NVIDIA GeForce GTX 1080 Ti/PCIe/SSE2
Driver Version: 4.6.0 NVIDIA 530.41.03
OpenGL Version: 4.6
Desktop Color Depth: 24 bits per pixel
Monitor Refresh Rate: 60 Hz
VendorID: 0x10de
DeviceID: 0x1b06
Revision Not Detected
Number of Monitors: 2
Number of Logical Video Cards: 1
Primary Display Resolution: 1920 x 1080
Desktop Resolution: 3840 x 1080
Primary Display Size: 20.75" x 11.65" (23.78" diag), 52.7cm x 29.6cm (60.4cm diag)
Primary Bus: PCI Express 16x
Primary VRAM: 11264 MB
Supported MSAA Modes: 2x 4x 8x 16x
Sound card:
Audio device: Nvidia GPU 82 HDMI/DP
RAM: 15913 Mb
VR Hardware:
VR Headset: None detected
UI Language: English
Total Hard Disk Space Available: 467875 MB
Largest Free Hard Disk Block: 51023 MB
Number of SSDs: 9
SSD sizes: 2000G,2000G,1000G,500G,63G,4510M,0B,0B,0B
Number of HDDs: 0
Number of removable drives: 0

Severity: High (This essentially makes TOOB parts unusable in anything other than the vertical orientation.)

Frequency: High (Always occurs)


When I adjust the length of a TOOB part via the slider in the parts manager, the position of the part attached to the fairing end of the part is adjusted incorrectly. when it should be adjusted  to match the location of the end of the TOOB.

Steps to reproduce:

  1. Start a new vehicle in the VAB.
  2. Select any of the TOOB parts from the structural section of the parts manager.
  3. Rotate the TOOB to any angle other than vertical.
  4. Attach anything to the fairing end of the TOOB part.
  5. Adjust the length of the TOOB fairing via the slider in the parts manager.
  6. Observe that the length of the TOOB's fairing changes as expected, but the change in location of the part that is attached to the TOOB does not match the change in location of the end of the TOOB.

Video Evidence:



Edited by The Space Peacock
added additional video submitted by author
Link to comment
Share on other sites

  • 2 months later...
  • 2 months later...

Reported Version: v0.1.5 (latest) | Mods: none | Can replicate without mods? Yes 
OS: Windows 10 | CPU: Intel Core i7 9750H | GPU: NVIDIA GeForce GTX 1650 | RAM16 GB

When I tried to change the length of the attached TOOB part through the part manager, instead of staying in place part shifted not only vertically but also horizontally. I have attached a video with bug

  1. Attach TOOB part to any other part
  2. Through part manager change its length and see result

Included Attachments:


Link to comment
Share on other sites

  • 2 weeks later...

Reported Version: v0.1.5 (latest) | Mods: none | Can replicate without mods? Yes 
OS: Windows 11 | CPU: 11th Gen Intel(R) Core(TM) i7-11700F @ 2.5GHz | GPU: NVIDIA GeForce RTX 3060 | RAM32 GB

If you place one of the adjustable tubes on its side and attach another part to the end of it and then adjust the length in the part manager the piece attached to the end of the tube will not move correctly. Instead of sticking with the tube and moving horizontally it moves vertically.

Included Attachments:

Link to comment
Share on other sites

  • Create New...