[1.3.0] Kerbal Engineer Redux 1.1.3.0 (2017-05-28)

[Mr.dobsonian]

Is this compatible with 1.12.2?

[antipro]

2 hours ago, Mr.dobsonian said:

Is this compatible with 1.12.2?

yes, Max Game Ver: 1.12.9 (using mod version 1.1.9.0)

Edited September 4, 2021 by antipro

[Mr.dobsonian]

29 minutes ago, antipro said:

yes, Max Game Ver: 1.12.9 (using mod version 1.1.9.0)

Cheers!

[Nicky21]

There's a bug with reporting "suicide burn countdown".

It reports just fine in normal time, but as soon as you time warp you get very different numbers.

[SiCaRiO31]

12 minutes ago, Nicky21 said:

There's a bug with reporting "suicide burn countdown".

It reports just fine in normal time, but as soon as you time warp you get very different numbers.

I trought it was just my install. Yes it happens when you warp, and I dont remember happening before.

[Krazy1]

11 hours ago, SiCaRiO31 said:

I trought it was just my install. Yes it happens when you warp, and I dont remember happening before.

It's wrong while warping and there's another bug in normal time for low, shallow approaches where the suicide burn starts after the impact time. I reported this long ago but here's another screenshot. 

 

[jinnantonix]

I am running KER 1.1.9.0 with KSP 1.12.2 and Galilean Planet Pack.

Intermittently KER stops displaying, and the KER tile goes black.  Does anybody know how to resolve this?

[Gordon Dry]

Within the last 6 weeks: 4 issues by me
https://github.com/jrbudda/KerbalEngineer/issues

there are some newer (cosmetical) commits at
https://github.com/lampeh/KerbalEngineer/tree/UImod

but neither a PR nor a compiled version of it.

Edited December 20, 2021 by Gordon Dry

[Fraktal]

On 10/6/2021 at 7:08 AM, Krazy1 said:

It's wrong while warping and there's another bug in normal time for low, shallow approaches where the suicide burn starts after the impact time. I reported this long ago but here's another screenshot. 

 

I think that's a deliberate performance shortcut.

Years-old posts in the KSP subreddit claim that KER's suicide burn calculations always assume a perfectly vertical descent, which is obviously going to be wrong if you descend at an angle. This is because to get the actual downwards thrust, KER would have to poll the craft's current attitude, get the engines' thrust vectors' angle away from pointing perfectly downwards, calculate the cosine of that angle and multiply the engine thrust with that. All of which would have to recalculated every single time your craft rotated even a microscopic fraction of a degree in any direction, including from engine torque caused by your craft's weight distribution not being 100% symmetric.

I'm sure you can imagine the performance impact of doing all that every couple of milliseconds in a game that's already one of the most brutal CPU hogs I know of.

End of line, you must kill your horizontal velocity before you begin the suicide burn. That is how the suicide burn countdown will be accurate - but even so, I always seem to end up killing my descent speed before reaching the surface if I start high enough, so I think the countdown might not calculate weight loss from fuel expenditure either.

[Krazy1]

6 hours ago, Fraktal said:

assume a perfectly vertical descent

Thanks for the info. Makes sense. It's a linear approximation and just uses the vertical component. But at least it shouldn't display an absurd value. If the suicide burn start time is after the impact time it should not display it at all. Bad data is worse than no data IMO. 

7 hours ago, Fraktal said:

doing all that every couple of milliseconds

I doubt it would be terrible. The KSP physics frame time is fixed at 20 ms. A CPU can do a COS in under a microsecond. The big performance hog is the ship part count because there are hundreds or thousands of interactions between the parts which also have springy joints. If you use the Trajectories mod, it does some fairly complex calculations like plotting the path of a ship through nonlinear atmospheric pressure. It shows the calculation time in the last tab and I'm seeing 1 ms/ 4% at the moment. I expect a suicide burn model would be similar. It could use some assumptions like a locally-flat world, constant gravity, constant mass and still be OK.  I'm not saying I have it figured out but it's seems doable.  

8 hours ago, Fraktal said:

you must kill your horizontal velocity before you begin the suicide burn. 

Then KER is right but that defeats the purpose of a suicide burn. A landing is a launch in reverse... you wouldn't launch vertical and then turn 90 deg. and try to do a horizontal burn to get to orbit, right? You could but it's not efficient.  

9 hours ago, Fraktal said:

the countdown might not calculate weight loss

I'm pretty sure it doesn't

[jrbudda]

On the topic of suicide burns: 

When I started maintaining KER the suicide burn did indeed only account for vertical velocity. I spent quite a bit of time in 2018 re-doing the impact/suicide calculations and adding the impact marker readout. It is a lot smarter than the previous 'vertical only' calculation, now a simulation instead of a simple equation, but it is by no means perfect. It will not account for air drag, nor weight loss during the burn. It uses approximations to estimate the angle of the craft at each step of the simulation, but as with most approximations, stray too far from the typical values and they break down. I tested it to my satisfaction using reasonably parabolic impacts and burns less than a minute or so. I did not test the calculation under on-rails warp, I would not suggest relying on the readout when that far away from the planet, nor when your horizontal velocity is on a higher order of magnitude than the vertical.

[Rakete]

Implementation proposal:

Additional dV and Burntimecountdown Readouts for the current stage 

• Considdering only active engines (currently all already staged engines are considdered in the calculation, which is usefull e.g. for the far future engines from nertea, but an additional readout for only the active engines would be good for multi-engine-SSTOs, where you turn off rapier in favor of nervas.

Refinement of dV-calculation: engines, that are slightly tilted out of the prograde-direction. E.g. nerteas radial spaceX-like capsules and radial Monofuel engines.... the stock dV readouts are more precise since they do the math of calculating the part of the exhaust, that is directed prograde.

 

Edited April 7, 2022 by Rakete

[mcniff]

How come I only have the ER 7500 part in the science section and not the chip as well? Both are researched and I have reinstalled the mod.

Could some other mod interfere somehow?

 

Edit: seems the mod kerbalism was the problem

Edited July 13, 2022 by mcniff

[Benjineer]

is there a way to make your own readout/function? for example minimum pitch angle to maintain 0 vertical speed when descending/ascending from a body with low twr.

[Brigadier]

11 hours ago, Benjineer said:

is there a way to make your own readout/function? for example minimum pitch angle to maintain 0 vertical speed when descending/ascending from a body with low twr.

Not from the current User Interface, which exposes only those parameters available to the KSP API.  You'd have to code this computation yourself and submit a PR on GitHub.

[Krazy1]

I'm using KSP Data Export mod to save CSV data during launches. It's missing some variables I want that are in KER. Has anyone attempted KER data export?

[CanOmer]

I can't detach Kerbal Engineering System (Part) and it blocks detachment of the Science Jr. that is attached to. I tried object thrower but it destroys the Science Jr as well. Is there any other soution to remove Kerbal Engineering System (Part)?

 

EDIT: I installed the KSP Part Volumes mod and now I can detach modded parts.

Edited October 10, 2023 by CanOmer

[CanOmer]

Dark transparent background goes away after few minutes. Any solution?

[fishyfungus]

probably my favorite mod

[fancycat]

I am sturggling a bit to understand this.  I am trying to use the land calculator, the "timer until burn start" is longer than the time until impact.  My timer also fluctuates wildly between 7 min and -300 seconds so i am really confused

[Krazy1]

8 hours ago, fancycat said:

I am sturggling a bit to understand this.  I am trying to use the land calculator, the "timer until burn start" is longer than the time until impact.  My timer also fluctuates wildly between 7 min and -300 seconds so i am really confused

There was some discussion about this above.  It works well in most conditions but not always.

 

[DeadJohn]

On 10/29/2023 at 6:09 PM, fancycat said:

"timer until burn start" is longer than the time until impact

Time until impact assumes no intervention. The vessel will continue to accelerate by gravity and crash in that much time if you take no action.

Timer until burn start is longer because you'll be slowing down after you activate braking engines.

Edited October 31, 2023 by DeadJohn
my 2nd paragraph makes no sense; don't know what I was thinking

[Krazy1]

I think we're talking about different things here...

10 hours ago, DeadJohn said:

Time until impact assumes no intervention. The vessel will continue to accelerate by gravity and crash in that much time if you take no action.

OK agreed.

10 hours ago, DeadJohn said:

Timer until burn start is longer because you'll be slowing down after you activate braking engines.

Then you would wait to start your suicide burn until after you crash. I think what you mean is the suicide burn length can be longer than the impact time. That is certainly possible. KER has both indicators: suicide burn length and suicide burn countdown. 

[DeadJohn]

4 hours ago, Krazy1 said:

Then you would wait to start your suicide burn until after you crash. I think what you mean is the suicide burn length can be longer than the impact time. That is certainly possible. KER has both indicators: suicide burn length and suicide burn countdown. 

Oh, yeah, you're correct. I had it backwards.

[Vasiliy]

Hi. Kerbal Engineer does not save some settings like "GUI Scale" or "VAB Overlay X Pos" (may be some others) after restarting the game.